-
GB/T 9757-2001
- 2001年09月06日
- 废止
本标准规定了溶剂型外墙涂料的产品分等、要求、试验方法、检验规则及标志、包装、贮存等要求。 本标准适用于以合成树脂为基料、与颜料、体质颜料及各种助剂配制而成的、施涂后能形成表面平整的薄质涂层的溶剂型外墙涂料。该涂料适用于建筑物和构筑物等外表面的装饰和防护。
涂料规范外墙溶剂
-
GB/T 21876-2008
- 2008年05月15日
- 作废
本标准规定了溶剂染料及染料中间体灰分的测定方法。 本标准适用于溶剂染料和染料中间体灰分的测定。
测定溶剂染料染料中间体灰分测定
-
ASTM B813-2010
- 现行
1.1 This specification establishes the requirements and test methods for liquid and paste fluxes for joining by soldering of copper and copper alloy tube and fittings in plumbing, heating, air conditioning, mechanical, fire sprinkler, and other similar systems.
Note 18212;This specification does not apply to fluxes intended for electronic applications.
1.2 Solder fluxes are to be tested in accordance with the requirements of this specification by an independent testing laboratory. Testing, measuring equipment, and inspection facilities shall be of sufficient accuracy and quality to comply with the requirements of this specification.
1.3 Units8212;The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 The following hazard caveat pertains to Sections 11-19. This standard does not purport to address the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
侵蚀性试验铜和铜合金腐蚀作用冲洗液体和膏状助焊剂电阻率软钎焊扩散因子变色粘度侵蚀性空调材料/设备规范铜合金管规范铜管规范腐蚀性饮用水规范电阻/电阻率消防喷水器无铅钖线加热系统接头(铜)接头(管/真空管设备)规范欧姆计助焊膏水管设施精密移液管滤渣冲洗焊料/焊接设备规范传播设备供水系统/分配制度
-
ASTM B813-2000e1
- 现行
铜钎焊助熔剂(材料)
-
ASTM B813-2000
- 现行
铜钎焊助熔剂(材料)
-
ANSI/AWS A5.22-2005
- 作废
规范焊接工程电焊条助熔剂(材料)
-
ANSI/AWS B2.1-1-019-2005
- 现行
This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using semiautomatic CO2 shielded flux cored arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for plate and structural applications.
焊接工程焊接工艺规范电弧焊接
-
AWS B2.1-1-020-1994
- 1994年01月01日
- 现行
焊接碳钢
-
EN ISO 26304-2011
- 2011年08月01日
- 作废
All-weld metalsChemical analysis and testingChemical compositionClassificationClassification systemsCored wire electrodeDelivery conditionsFiller metalFiller wireFluxesHigh-tensile steelsImpactMarksMechanical testingNotched bar impact workPropertiesSolid wire electrodesSpecification (approval)SteelsStrength of materialsSubmerged arc weldingSymbolsTensile strengthTestingWeld metalWeldingWelding electrodesWelding engineeringWelding filler metalsYield strength
-
GB/T 38730-2020
- 2020年04月28日
- 现行
本标准规定了水增溶力和水乳化力的测定方法。本标准适用于干洗洗涤剂或在洗槽中浓度通常为3g/L~5 g/L及其他适宜浓度的辅助产品。本标准不适用于溶剂和水中含有较高浓度表面活性剂的附属产品,如用于刷洗或喷洒的化学洗涤产品。