纺织行业知识服务平台
}
首页>知识导航 > 纺织材料 > 复合材料 > 金属基复合材料
发布时间 收起
展开更多
强制性标准 收起
中标分类 收起
展开更多
标准状态 展开
标准组织 展开
来源数据库 展开
相关度
订阅
至 收起
  • 服务由 质检出版社 提供

    GB/T 34558-2017 - 2017年10月14日 - 现行
    本标准界定了金属基复合材料的术语和定义。 本标准适用于金属基复合材料及其相关领域的标准化文件和技术文件。
  • 服务由 质检出版社 提供

    GB/T 32498-2016 - 2016年02月24日 - 现行
    本标准规定了金属基复合材料拉伸试验方法的术语和定义、符号和说明、原理、试验设备、试样、试验要求和试验报告。 本标准适用于颗粒增强金属基复合材料及短纤维增强金属基复合材料的室温拉伸试验。
  • 服务由 质检出版社 提供

    GB/T 41739-2022 - 2022年10月12日 - 现行
    本文件规定了应用冷热循环实时检测金属基复合材料尺寸稳定性的试验原理、样品、测试装置及测试程序、试验结果,以及试验报告等。本文件适用于铝基复合材料(冷热循环温度范围:20℃~150 ℃)、镁基复合材料(冷热循环温度范围:20 ℃~150 ℃)、铁基复合材料(冷热循环温度范围:20 ℃~490 ℃)的尺寸稳定性的测定。
  • 服务由 质检出版社 提供

    GB/T 32496-2016 - 2016年02月24日 - 现行
    本标准规定了测定颗粒增强与单向连续纤维增强金属基复合材料中颗粒或纤维体积含量的方法原理、试验设备、试样、试验方法、试验结果以及试验报告等。
  • 服务由 WF 提供

    HB 7616-1998 - 1998年06月26日 - 现行
    本标准规定了单向(0°)长纤维增强金属基复合材料层板拉伸性能试验的试样、试验条件、试验设备、试验步骤和试验结果处理。  本标准适用于室温~400℃范围内,测定单向(0°)长纤维增强金属基复合材料层板的抗拉强度、拉伸杨氏模量、条件切线模量、泊松比和应力-应变曲线。
    纤维增强复合材料金属基复合材料复合材料层板拉伸性能试验方法
  • 服务由 WF 提供

    HB 7617-1998 - 1998年06月26日 - 现行
    纤维增强复合材料金属基复合材料复合材料层板弯曲性能试验方法
  • 服务由 WF 提供

    JIS H7006-1991 - 现行
    この規格は,主として繊維を複合した金属基複合材料に関する主な用語及びその定義について規定する。
    复合材料纤维金属丝粉末冶金金属词汇
  • 服务由 WF 提供

    JIS H7401-1993 - 1993年07月01日 - 现行
    纤维复合材料金属材料(按形状分)容积测量体密度
  • 服务由 WF 提供

    ASTM D3552-1996(2007) - 现行

    This test method is designed to produce tensile property data for material specifications, research and development, quality assurance, and structural design and analysis. Factors that influence the tensile response and should be reported include the following: material, methods of material preparation and lay-up, specimen stacking sequence, specimen preparation, specimen conditioning, environment of testing, specimen alignment and gripping, speed of testing, time at temperature, and volume percent reinforcement. Properties, in the test direction, which may be obtained from this test method include the following:

    5.1.1 Ultimate tensile strength,

    5.1.2 Ultimate tensile strain,

    5.1.3 Tensile modulus of elasticity, and

    5.1.4 Poissons ratio.

    1.1 This test method covers the determination of the tensile properties of metal matrix composites reinforced by continuous and discontinuous high-modulus fibers. Nontraditional metal matrix composites as stated in also are covered in this test method. This test method applies to specimens loaded in a uniaxial manner tested in laboratory air at either room temperature or elevated temperatures. The types of metal matrix composites covered are:

    1.1.1 Unidirectional - Any fiber-reinforced composite with all fibers aligned in a single direction. Continuous or discontinuous reinforcing fibers, longitudinal and transverse properties.

    1.1.2 0/90 Balanced Crossply - A laminate composed of only 0 and 90 plies. This is not necessarily symmetric, continuous, or discontinuous reinforcing fibers.

    1.1.3 Angleply Laminate - Any balanced laminate consisting of theta plies where theta is an acute angle with respect to a reference direction. Continuous reinforcing fibers without 0 reinforcing fibers (that is, (177;45)ns, (177;30)ns, and so forth).

    1.1.4 Quasi-Isotropic Laminate - A balanced and symmetric laminate for which a constitutive property of interest, at a given point, displays isotropic behavior in the plane of the laminate. Continuous reinforcing fibers with 0 reinforcing fibers (that is, (0/177;45/90)s, (0/177;30)s, and so forth).

    1.1.5 Unoriented and Random Discontinuous Fibers

    1.1.6 Directionally Solidified Eutectic Composites

    1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

    This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    航空航天运输航空运输复合材料纤维增强的纤维叠层板材材料金属性能航天技术拉伸载荷拉伸试验测试
  • 服务由 WF 提供

    ASTM D3552-1996(2002) - 现行
    航空航天运输航空运输复合材料纤维增强的纤维叠层板材材料金属性能航天技术拉伸载荷拉伸试验测试
1 2 3 下一页 GO
回到顶部